Rupert Neve Designs Portico 5012 Duo Mic Pre-Amp

Rupert Neve Designs Portico 5012 Duo Mic Pre-Amp

£1,733.00

Clear

Description

Rupert Neve Designs Portico 5012 Duo Mic Pre-Amp

Features

The Rupert Neve Portico 5012 is a dual channel mic pre featuring Neve’s custom input and output transformer designs. In addition to individually selectable phase, mute, phantom power and a fully sweepable high pass filter, the 5012 incorporates a “Silk” circuit which yields the rich warmth and presence of the renowned classic designs.

Microphone Input

The microphone input is balanced but not floating, being a variant of an instrumentation ampliferusing a “Transformer-Like-Amplifier” (T.L.A.) configuration with a toroidal Common ModeRejection Low Pass Filter that excludes frequencies above 150 kHz.The T.L.A. is followed by an actual input transformer permitting a full +25 dBu input signal tobe handled at unity gain without an input pad over the whole audio spectrum.This combines the advantages of both an “Electronically Balanced” and true transformer input.When the Phantom voltage is switched off, this input serves as a very high quality line input with an impedance of 10,000 ohms.

 


Low Noise, Low Distortion Operation

Much care was given in designing the 5012 to produce as little noise and non-harmonic distortion as possible. Carefully implemented signal paths and Class A operation are a large part of the 5012’s sweet, whisper quiet performance.

 


 

Why Transformers?

A complete discussion on transformers is out of place at this point but a technical discussion will be posted at a later date. Here it is helpful to review some of the essentials where it will be seen that a design needs to be viewed as a whole, not simply from the point of view of a single component.

The fine subtleties of circuit design relating to sonic performance are gradually becoming more clearly understood. For example, research has shown conclusively that frequencies above 20 kHz affect the way in which humans perceive sound quality. But, long before scientific evidence emerged a substantial body of musicians and engineers knew that equipment with apparently the same technical measurements could sound very different.

Incredibly small amounts of musically dissonant odd harmonics have a disastrous effect on the sound quality. Extraneous noise or interference that finds its way into a signal path seriously impairs performance of the whole chain.

Many control rooms make use of outboard gear that is not well protected from external signals. Poor grounding of such equipment can be a serious problem. “Electronically balanced” circuits much used in modern equipment, can give very good measurements on the test bench but they do not provide adequate rejection of the stray fields found in every working environment.

Input and output circuits must be freed from ground dependence so that only the “wanted” signal enters and leaves the processing path. Transformers are the ideal solution. The sweet and silky sound of my classic old favourite consoles was achieved with big transistors and large high quality transformers. Rupert Neve Designs Portico modules achieve similar quality today without the bulk or the cost.

In order that modules can work together as would be expected (i.e. in a proprietary console configuration) without producing hum, R.F. interference, or other interactions, the connecting interfaces, grounding, levels and impedances must receive careful attention. Each Portico module is a complete integral signal processor that delivers its specified performance independently. This is one of the reasons we use transformers.

Technical Specs of the Rupert Neve Designs Portico 5012

Input:    

Balanced, using “Transformer-Like-Amplifier” (T.L.A.) with toroidal Common Mode Rejection Low Pass Filter that excludes frequencies above 150 kHz.

The T.L.A. is followed by an actual input transformer permitting a full +26 dBu input signal to be handled at unity gain without an input pad over the whole audio spectrum.

Combines the advantages of both an “Electronically Balanced” and true Transformer input.

When the Phantom voltage is disabled, this input serves as a very high quality Line Input.

     
Input Impedance: 10,000 Ohms + or 20%  
     
Noise:    

Measured at Main Output:

Input terminated with 150 Ohms.

Measured over band limited 22Hz-22kHz, Unweighted:

With Gain at Unity: Better than 100 dBu.
  With Gain at 66 dB: Better than 62 dBu
  Equivalent Input Noise (E.I.N.) Better than 128 dBu
Frequency Response:    

Main Output, no load:

@ 10 Hz, 0.2 dB
  @ 160 kHz 3 dB
Buss Output  
@ 10 Hz 0.2 dB
  @ 160 kHz 3 dB
High Pass Filter:    

Swept Frequency continuously variable from 20 Hz to 250 Hz.

Slope: 12 dB/Octave.
     
Gain:    

Switched Gain from Unity to +66dB in 6 dB steps.

   
     
Trim:    

Continuously adjustable potentiometer from 6dB to +6dB with reference to setting on the Gain Switch.

     
Maximum Output Level:    

Balanced and Floating Transformer Output from 20 Hz to 40 kHz: +25 dBu. (Clips at just over +26 dBu)

     
Mute:    

Mutes Main Output only. (i.e. Monitor remains Live)

 
     
Total Harmonic Distortion and Noise:    

Main Output

@ 1kHz, +20 dBu output
level, no load:

Better than 0.001%.
(No high order Harmonics)

Silk Engaged:

Approximately 0.2% Second Harmonic

Main Output

@ 20Hz, +20 dBu output
level, no load:
Better than 0.01%.

Buss Output

@ 1kHz, +20 dBu output
level, no load, measured at the output:
Better than 0.002%.
SILK:    

The 5012 uses mainly single-sided amplifier circuitry that excludes any possibility of crossover distortion.The “SILK” button reduces negative feedback and adjusts the frequency spectrum to provide a very sweet and musical performance.

     
Buss Output:    

The Buss Output is designed to feed other Portico Series modules with Buss Inputs.

     
Crosstalk:    

Measured Channel to Channel:

Better than 90 dB @ 15kHz.  
     
Phantom Power: +48 Volts DC +/- 1%  
     
Main Power Required: (From External Power Unit) Voltage Range, 9 to 18 Volts DC.
     
Current consumption: @ 9VDC = 1.3 A typical  
  @12VDC = 1A typical  
  @15VDC= 800 mA typical  
  @18VDC= 650 mA typical  
     
Rear Panel Power Connector: 5.5mm X 2.1mm DC jack, Center Positive

Product Demonstration Services @ Kazbar Systems

If you are a professional producer, sound designer, engineer or are part of a commercial studio and wish to auditions a product on-site in your studio, then you’re in the right place.

We specialize in hands on one-to-one demonstrations of pro audio equipment such as; monitors & outboard and also provide demoonstrations for our range of botique synthesizers and effects.

Contact us to arrange your demo now!